Kuala Lumpur | Selangor | Shah Alam | Klang | Petaling Jaya | Subang Jaya | Cyberjaya | Rawang | Kajang | Bangi | Port Klang | Pulau Indah | Johor Bahru | JB | Pasir Gudang | Pengerang | Kulai | Batu Pahat | Muar | Kluang | Melaka | Bukit Rambai | Sungai Udang | Masjid Tanah | Alor Gajah | Nilai | Seremban | Senawang | Ipoh | Taiping | Penang | George Town | Batu Kawan | Bayan Lepas | Bukit Mertajam | Perai | Kulim | Sungai Petani | Kuantan | Gebeng | Kemaman | Kuala Terengganu | Kota Bharu | Kuching | Bintulu | Miri | Sibu | Kota Kinabalu | Labuan | Brunei

The Elcometer 142 Dust Tape Test Kit allows assessment of the quantity and size of dust particles on surfaces prepared for painting.

Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and sub-standard coating finish.

The Elcometer 139 Amine Blush Swab Test Kit is a rapid colourimetric test designed solely for the use in the quick and immediate identification of amine blush (carbamates) on the surface of coatings using surface swabs. The presence of amine blush is indicated by a visual change of colour of the test solution when compared with a control sample.

The Elcometer 139 Amine Blush Chip Screen Test Kit is a rapid colourimetric test designed solely for the use in the quick and immediate identification of amine blush (carbamates) on the surface of coatings using small chips or shavings.

The presence of amine blush is indicated by a visual change of colour of the test solution when compared with a control sample.

Measuring the level of contaminants on a surface prior to application of the coating is essential to ensure the quality of the coating and that its optimum lifetime is achieved.

If the coating is applied to a contaminated surface, which is not properly prepared, it could fail prematurely resulting in costly recoating and high maintenance costs.

Incorporating a flat sensor, the Elcometer 138 Conductivity Meter can measure the conductivity of a solution from a single drop of a sample.

Users can either place a sample on the meter’s flat sensor or immerse the meter’s sensor directly into the solution under test.

The Elcometer 138 Bresle Salt Meter enables highly precise measurements to be obtained from a single drop.

It is essential that the level of contaminants on a surface is measured prior to the application of the coating to ensure the quality of the coating and that its optimum lifetime is achieved.

If the coating is applied to a contaminated surface, which is not properly prepared, it could fail prematurely resulting in costly re-coating and high maintenance costs.

The Elcometer 135C Bresle Test Patches determines the concentration of soluble salts on uncoated surfaces in accordance with the ISO 8502-6 test method.

Elcometer 135B Original Bresle Patches are used to determine surface chloride contamination and are self-adhesive rubber film patches with a sealed compartment for sampling soluble impurities from steel surfaces with a suitable solvent.

Elcometer 135B Bresle Patches can also be used with the Elcometer 138C Bresle Salt Kit.

The Elcometer 134S Chloride Ion Test Kit for Surfaces allows the surface to be tested for chloride salts prior to application of a coating.

Chloride salts left on the surface before the first coat is applied can result in the coating system being forced off the surface by corrosion or blistering before the full life of the coating has been reached.

The Elcometer 134 CSN Chloride, Sulphate & Nitrate Test Kit is designed to accurately measure surface chloride, sulphate and nitrate ions in minutes and offers a single kit solution for testing in the field.

All the components of the Elcometer CSN Test Kits are pre-measured and pre-dosed for trouble free testing.

The Elcometer 130 Soluble Salt Profiler provides fast and accurate measurement of the level and density of soluble salts – over 4 times faster than other Bresle equivalent methods.

The new Elcometer 130 Soluble Salt Meter allows you to complete a Bresle equivalent test in just over two minutes.

The Elcometer 130 Salt Contamination Meter quickly and accurately measures the level of soluble salts on surfaces over 4 times faster than Bresle equivalent test methods.

Wet Sponge Technique: A low voltage is applied to a moist sponge. When the sponge moves over a coating flaw, liquid penetrates to the substrate and completes an electrical circuit, setting off the alarm.

High Voltage Technique: The high voltage, or porosity technique, can be used to test coatings up to 25mm (1”) thick and is ideal for inspecting pipelines and other protective coatings. Coatings on concrete can also be tested using this method.

A power supply generates a high voltage DC to a probe.

A complete range of accessories including rolling springs, wire brush probes and batteries.

The Elcometer 260 UV Pinhole Flashlight is battery powered and housed in a rugged aluminium case providing a quick, low cost method of testing coatings for pinholes.

Featuring a 3-Watt purple light emitting diode, the Elcometer 260 UV flashlight has a beam wavelength of 405nm (±5nm), which the human eye perceives as a purple light.

ElcoPatch™ ensures a consistent method of high quality repair to reassure asset owners and contractors.

ElcoPatch™ makes repairing coating flaws simple and consistent for long term protection.

The ElcoPatch™ kit comes with everything you need to repair flaws – ideal for use with most approved coatings in 50ml (1.8oz) tubes.

The Elcometer 215 Oven Data Logger is the easy-to-use oven temperature profile solution, used to measure and store the temperature profiles of both the sample and the oven during the cure process.

The Elcometer 7410 Concrete Moisture Meter is an accurate and easy to use non-invasive instrument for non-destructive measurement of moisture content of concrete.

The electrodes transmit parallel low frequency signals, calibrated to give average moisture content by comparing the change in impedance between damp and acceptably dry concrete.

The Elcometer 7000 Digital Moisture Meter range offers accurate and easy to use moisture measurement.

Available in two versions, the Concrete Moisture Meter has a non-invasive probe that emits a radio frequency to penetrate the surface to detect moisture. Ideal for rapid surveys of solid wall, floors and ceramic tiles.

The Elcometer Qualicoat Powder Coating Inspection Kit provides the various test instrumentation required to meet the high standards of the Qualicoat Organisation.

The Qualicoat Organisation brings together the ideals of several National Coating Associations into one quality label for powder coatings on aluminium architectural components.

The Elcometer Hazardous Area Inspection Kit is a protective coating inspection kit suitable for use in hazardous areas where electronic equipment is prohibited.

The kit provides all the tools required for the on-site inspection of a coating, including surface profile, dewpoint, relative humidity, both wet and dry film thickness and also adhesive testing.

The Elcometer Protective Coating Inspection Kit 6 is a comprehensive kit that incorporates all the key gauges and inspection accessories required to assess a structure before, during and after the coating has been applied.